Rate this webpage

NCP1337: Controller, Quasi-Resonant Current Mode, with Overpower Compensation

Datasheet: PWM Current-Mode Controller for Free Running Quasi-Resonant Operation
Rev. 6 (162kB)
Product Overview
»View Reliability Data
»View Material Composition
» Product Change Notification
The NCP1337 combines a true current mode modulator and a demagnetization detector which ensures full Borderline/Critical Conduction Mode in any load/line conditions together with minimum drain voltage switching (Quasi−Resonant operation). The transformer core reset detection is done internally, without using any external signal, due to the Soxyless concept. The frequency is internally limited to 130 kHz, preventing the controller to operate above the 150 kHz CISPR−22 EMI starting limit.
By monitoring the feedback pin activity, the controller enters skip mode as soon as the power demand falls below a predetermined level. As each restart is softened by an internal soft−skip™, and as the frequency cannot go below 25 kHz, no audible noise can be heard.
The NCP1337 also features an efficient protective circuitry which, in presence of an overcurrent condition, disables the output pulses and enters a safe burst mode, trying to restart. Once the default has gone, the device auto−recovers. Also included is a bulk voltage monitoring function (known as brown−out protection), an adjustable overpower compensation, and a VCC OVP. The controller immediately restarts after any of these conditions, unless the fault timer has timed out. Finally, an internal 4.0 ms soft−start eliminates the traditional startup stress.

NCP1338 vs NCP1337: When a BO condition is applied, both controllers stop. When the BO condition is removed, NCP1337 doesn't restart if the fault timer has timed out; whereas NCP1338 always restarts (if Vcc is higher than 12 V).
Features   Benefits
  • Valley switching/QuasiResonant Operationn
  • High efficiency and low EMI
  • Soft-skip Mode with Minimum Switching Frequency for Standby
  • High efficiency in light load conditions, with noise-free operation
  • Current-Mode with Overpower Compensation
  • Auto-Recovery Short-Circuit Protection Independent of Auxiliary Voltage
  • Overvoltage Protection
  • Brown-Out Protection
  • Two Externally Triggerable Fault Comparators (one for a disable function, and the other for a permanent latch)
  • Internal 4.0 ms Soft-Start
  • 500 mA Peak Current Drive Sink Capability
  • 130 kHz Max Frequency
  • Internal Leading Edge Blanking
  • Internal Temperature Shutdown
  • Direct Optocoupler Connection
  • Dynamic Self-Supply with Levels of 12 V (On) and 10 V (Off)
  • SPICE Models Available for TRANsient and AC Analysis
  • These are Pb-Free Devices
Applications   End Products
  • AC-DC Adapters for Notebooks, etc.
  • Offline Battery Chargers
  • Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
  • Consumer Electronics (DVD Players, Set-Top Boxes, TVs, etc.)
Budgetary Price/Unit
Case Outline
NCP1337DR2G Active, Not Rec 
Halide free
NCP1337 SOIC-7 751U 1 260 Tape and Reel 2500 $0.62
NCP1337PG Lifetime
Halide free
NCP1337 PDIP-8 626B NA Tube 50 $0.4195
Market Leadtime (weeks) : Contact Factory
FutureElectronics   (2020-08-19 00:00) : >1K
PandS   (2020-09-14 00:00) : <1K
Market Leadtime (weeks) : Contact Factory
ON Semiconductor   (2020-09-02 00:00) : 4,300
Case Outlines
626B    751U   
NCP1337: Controller, Quasi-Resonant Current Mode, with Overpower Compensation
NCP1337: Controller, Quasi-Resonant Current Mode, with Overpower Compensation
Previously Viewed Products
Clear List

Your request has been submitted for approval.
Please allow 2-5 business days for a response.
You will receive an email when your request is approved.
Request for this document already exists and is waiting for approval.