Connectivity Bluetooth Low Energy
Topic | Replies | Views | Activity | |
---|---|---|---|---|
KB: RSL10 Power Consumption Evaluation Guide
[RSL10 - Knowledge Base] Table of Contents Power Profiler Measurement Equipment Setup Hardware Setup Software Setup Connectable/Non-Connectable Advertising Advertising Interval Connection Interval Tx Payload Tx Pow… |
![]() ![]() |
13 | 2344 | May 19, 2022 |
KB: RSL15 Power Consumption Evaluation Guide
[RSL15 - Knowledge Base] Table of Contents Power Profiler Measurement Equipment Setup Hardware Setup Software Setup Evaluating Current Measurements Power Profiler The spreadsheet tool included in the topic link… |
![]() |
2 | 71 | May 19, 2022 |
KB: RSL15 Power Consumption and Battery Estimator
[RSL15 - Knowledge Base] Introduction The purpose of this spreadsheet and the corresponding VBA user-forms is to generate power and current consumption estimates when the RSL15 is operating in a variety of commonly u… |
![]() |
3 | 57 | May 19, 2022 |
KB: Getting Started with RSL15
RSL15 is an ultra−low power secure Arm® Cortex®−M33 processor−based Bluetooth Low Energy 5.2 wireless MCU. But what can it do? Thats entirely up to you and heres how you get started! Step 1 - Request an RSL15 evaluati… |
![]() |
2 | 712 | November 22, 2021 |
KB: RSL10 Power Consumption and Battery Estimator
[RSL10 - Knowledge Base] Introduction The purpose of this spreadsheet and the corresponding VBA user-forms is to generate power and current consumption estimates when the RSL10 is operating in a variety of commonly u… |
![]() |
2 | 2049 | March 12, 2021 |
KB: Getting set up with the RSL10 SDK & Eclipse IDE
Question What steps are necessary to access the RSL10 SDK and set up the Eclipse based tools Recommendation Go to the RSL10 product page page Use the download buttons on the main page Download and read the R… |
![]() ![]() ![]() ![]() ![]() |
17 | 4371 | January 14, 2022 |
About the Bluetooth Low Energy category
|
![]() |
0 | 1505 | June 8, 2020 |
Battery measurement
|
![]() ![]() ![]() |
2 | 614 | May 25, 2022 |
KB: How to set TX power level in BLE applications
|
![]() ![]() ![]() |
3 | 1002 | May 24, 2022 |
Trying to read data from uart
|
![]() ![]() ![]() ![]() |
13 | 691 | May 24, 2022 |
How can I correctly collect a sequence of audio samples (from DMIC) in Arm Cortex memory for further processing in LPDSP32?
|
![]() ![]() ![]() ![]() |
6 | 430 | May 23, 2022 |
How to extend customer service length
|
![]() ![]() ![]() |
11 | 157 | May 23, 2022 |
What features are not supported by RSL10?
|
![]() ![]() ![]() |
2 | 57 | May 20, 2022 |
New to Eclipse and OnSemi and want to debug to UART
|
![]() ![]() ![]() ![]() ![]() |
18 | 1397 | May 20, 2022 |
KB: How to enable DIO13,DIO14 and DIO15 for normal DIO function?
|
![]() ![]() ![]() ![]() ![]() |
10 | 803 | May 20, 2022 |
Streaming data with notification causes reset
|
![]() ![]() |
6 | 71 | May 19, 2022 |
How to set pairing options for Just Works?
|
![]() ![]() |
1 | 34 | May 19, 2022 |
KB: How to support BLE passkey paring mode
|
![]() ![]() ![]() ![]() |
7 | 948 | May 18, 2022 |
On semi IDE RSL10 FOTA post build failure
|
![]() ![]() |
1 | 57 | May 13, 2022 |
How to use NVR1 for saving application data?
|
![]() ![]() ![]() |
4 | 85 | May 13, 2022 |
Device serialization number in NVR
|
![]() ![]() |
1 | 82 | May 12, 2022 |
DIO output to 1.5-2V in sleep mode ,which should be 0V
|
![]() ![]() |
1 | 73 | May 11, 2022 |
BLE abstraction for DISS - can't change security level
|
![]() ![]() |
4 | 104 | May 10, 2022 |
Ble_peripheral_server example
|
![]() ![]() |
1 | 114 | May 9, 2022 |
How to check ECC for flash corruption?
|
![]() ![]() ![]() |
4 | 85 | May 9, 2022 |
RSL 10 advertisement event tracking
|
![]() ![]() |
2 | 388 | April 29, 2022 |
KB: Using DIO PIN to show TX and RX activity on RSL10
|
![]() |
2 | 121 | April 29, 2022 |
Non connectable ADV mode
|
![]() ![]() |
2 | 130 | April 28, 2022 |
Troble saving the bonded devices list in NVR2
|
![]() ![]() |
1 | 85 | April 27, 2022 |
Reduce FOTA download speed
|
![]() ![]() |
3 | 156 | April 26, 2022 |