NCV7702B: Motor Driver, Dual H-Bridge, 1.0 A

Overview
Specifications
Packages
Applications
Datasheet: Motor Driver, Dual H-Bridge, 1.0 A
Rev. 1 (107.0kB)
»View Material Composition
»Product Change Notification (2)
Product Overview
Product Description
This dual full−bridge driver IC is intended for 14 V automotive stepper and DC motor applications. Its four half−bridge outputs are configured as two channels and are programmed by six TTL compatible inputs, allowing flexible control of bridge operation. The device operates in standby mode, run mode, or brake mode and typically consumes less than 1 uA while in standby. In run mode, each half−bridge output can deliver load current in either direction. Brake mode activates the low side transistors or high side transistors at the selected outputs. On−chip recirculation diodes are provided, and the IC has multiple fault protection modes.
Overcurrent detection protects against shorted loads between outputs and shorts to supply or ground at each output. An overcurrent fault condition activates an internal timer, which modulates faulted outputs at low duty cycle. An overcurrent condition in one channel does not affect operation in the other. Overvoltage and overtemperature detection are also provided, and turn off all bridge outputs during these fault conditions. Recovery from all fault conditions is automatic; the IC will resume normal operation in its previously selected mode upon fault resolution. Diagnostic ability is provided by two open−collector STATUS outputs which report the fault status of each channel independently during overcurrent faults, and together during overvoltage or overtemperature faults.
Features
 
  • Single 7 V to 16 V Supply
  • Low Standby Current: < 1.0 µA Typical
  • 3.3 V / 5 V Compatible Inputs
  • Independent Channel Enable
  • Full-Bridge, Half-Bridge, High Side or Low Side Drive
  • On-Chip Recirculation Diodes
  • Fault Protection with Automatic Recovery
  • Overcurrent Protection
  • Overvoltage Protection
  • Overtemperature Protection
  • Fault Diagnostic STATUS Outputs
  • Internally Fused Leads in SO24L Package
  • AEC Qualified
  • PPAP Capable
Applications   End Products
  • DC or Stepper Motors
  • Relays or Solenoids
  • Unipolar or Bipolar Loads
 
  • Automotive
Technical Documentation & Design Resources
Data Sheets (1) Package Drawings (1)
Availability and Samples
Product
Status
Compliance
Description
Package
MSL*
Container
Budgetary Price/Unit
Type
Case Outline
Type
Qty.
NCV7702BDWR2G Active
AEC Qualified
PPAP Capable
Pb-free
Halide free
Motor Driver, Dual H-Bridge, 1.0 A SOIC-24 751E-04 3 Tape and Reel 1000 Contact Sales Office
Moisture Sensitivity level (MSL) for surface mount devices (lead free measured at 260°C reflow, non lead free at 235°C reflow)
Market Leadtime (weeks) :
Datasheet: Motor Driver, Dual H-Bridge, 1.0 A
Rev. 1 (107.0kB)
»View Material Composition
»Product Change Notification (2)
Product Overview

Product Compliance Status Description Type VM Min (V) VM Max (V) VCC Min (V) VCC Max (V) IO Max (A) IO Peak Max (A) Step Resolution Control Type Feedback Method Current Sense Regulator Output Fault Detection Flyback Protection RDS(on) Typ (Ω) Package Type
 AEC Qualified 
 PPAP Capable 
 Pb-free 
 Halide free 
 Active     Motor Driver, Dual H-Bridge, 1.0 A     7   30   7   16   0.001   1.6     Parallel       No 
 Over-Current 
 Thermal 
     SOIC-24 
Previously Viewed Products
Clear List

New Products
 

NCV7518  FLEXMOS Hex Low-Side MOSFET Pre-Driver

  • 16-bit SPI with parity and frame error detection
  • Ratiometric diagnostic references and currents to battery voltage
  • Scalable to load

STK5Q4U352J-E  STK5Q4U362J-E  Inverter IPMs for 3-phase Motor Drive

  • Internal bootstrap circuit for high side pre-driver enables single control power supply
  • Low voltage level control inputs and status outputs are directly compatible with microcontrollers
  • Compact DIPS3 package uses newly developed structure for higher heat dissipation